| Step 16. Install the battery inside the handheld
transmitter after setting the transmitter DIP switches to match the DIP switches
in the receiver. The battery is a 12 volt type A23, 23A, MN-21, or equivalent,
commonly found with camera supplies. Step
17. Mount the remote holder over the ceiling fan's wall switch using the supplied
wall plate screws. If you have rocker-style switches, break off the inside tabs
that are used to mount to a standard toggle switch wall plate.
The transmitter can be placed on the remote
holder for convenience or safekeeping. |
Step 18. When the installation is complete,
restore power at main electrical panel. Then, turn on the wall switch. The light
kit should turn On. If the light remains Off, turn off the power at the wall switch.
Pull the light kit's pull chain to turn the light On.
|
Step 19. Press the remote control's High
speed button (3 raised dots). The fan should start and reach its maximum speed.
If the fan does not start, or is turning too slow, turn off the power at the wall
switch. Pull the fan's pull chain to change speeds. Reapply power and try High
speed again. Repeat this procedure until you have confirmed that the fan's pull
chain is set to High speed. |
WARNING!
Do not use the pull chain to operate the light. Pulling the chain while power
is applied can damage the receiver. It is recommended to shorten the pull chain(s)
to prevent accidental use. |
|
| WARNING!
Do not use the pull chain switch to change speeds. Pulling the chain while power
is applied can damage the receiver or ceiling fan. | |
| Step 20. Turn On wall switch, the light will turn
On at maximum brightness. Light
Operation:
· Press and quickly
release either of the 2 light buttons on the hand held remote to turn the light
OFF or ON. Pressing the RIGHT button will turn the light On at full brightness.
Pressing the LEFT button will turn the light On at low brightness.
·
Press and hold the RIGHT light button for more than 1 second to turn the light
ON and decrease from full brightness to OFF.
·
Press and hold the LEFT light button for more than 1 second to turn the light
ON and increase from low brightness to OFF.
·
Release the light button when the desired light level is reached.
·
Continue to hold the light button to repeat the cycle.
·
While the light is ON, holding the RIGHT light button will decrease the light
brightness and holding the LEFT light button will increase the light brightness.
· Turning the light OFF with either
key resets the dimming function. | |
| Fan Operation:
·
Press the High, Medium, or Low speed buttons to turn the ceiling fan ON at the
desired speed.
· Press the fan
OFF key to turn the ceiling fan OFF. For best fan operation: Allow the ceiling
fan motor to start on High, then select the desired speed.
·
You can change to any speed at any time by pressing the appropriate fan speed
button.
Manual
Light Switch Operation:
To turn the
lights ON without the transmitter, turn OFF the wall switch for 5 seconds, then
turn the wall switch back ON. The light will turn ON at maximum brightness, and
the fan will be OFF. For everyday operation, leave the wall switch ON. However,
if the control will not be used for an extended period of time (several days),
turn the wall switch OFF. | |
| ADAPT·TOUCH Troubleshooting |
| SYMPTOM
1. No functions operate | |
| POSSIBLE CAUSE
a. Main power not restored.
b. Fan pull chain not set to High.
c. Light pull chain not set ON. d.
Receiver wiring incorrect. e. Transmitter and receiver
dip switches do not match. f. Battery too weak.
| |
| SOLUTION
a. Replace fuse. Turn ON circuit breaker. Turn ON wall switch.
b. Turn OFF power at wall switch or main electric panel.
Set fan to High speed.
c. Set light kit to ON.
d. Verify wiring connections. e.
Set transmitter and receiver to same dip switch settings. f.
Replace with new alkaline battery. | |
| 2. Operates only at close
range | |
|
| a. Replace with new alkaline
battery. | |
| 3. Inconsistent operation.
| |
| a. RF interference.
b. Continuing RF Interference | |
| a. Replace with new alkaline
battery. | |
CASABLANCA
FAN COMPANY
ADAPT·TOUCH CONTROL LIMITED WARRANTY
The Casablanca Fan Company makes the following limited warranty
to the original purchaser of the ADAPT·TOUCH Control ("Control"):
Your Control is warranted to be free from defects in material and workmanship
for a period of one year from the date of sale. If the Control malfunctions or
fails within the warranty period due to a defect in material or workmanship we
will replace it free of charge. IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL,
THIS WARRANTY AND ANY IMPLIED WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. THIS
WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED
WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO ANY CONTROL, IS EXPRESSLY LIMITED
TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH CONTROL. This warranty
excludes malfunctions or failures, which were caused by repairs by persons not
authorized by us, mishandling, improper installation, modifications, or damage
to the Control while in your possession, or unreasonable use. This warranty does
not apply to batteries or to deterioration or damage to the product caused by
the use of faulty batteries. To obtain a replacement, return your Control postage
prepaid along with proof of purchase to Casablanca Fan Company Service Department
761 Corporate Center Drive, Pomona, California 91768. IN NO EVENT SHALL CASABLANCA
FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. SOME STATES DO
NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
|
